See Availability

 

Everyone has their unique rationale on the subject of How to Install a Bathtub.

Mounting a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old bathtub is conveniently available, the task can move speedily; if you need to open a wall to get rid of the old bathtub as well as position the new tub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will need an assistant to leave the old tub and also embeded in the new one. See to it you have actually qualified on your own for the job and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Chances are you might require a professional plumber to make tube links.
This write-up will certainly aid you set up a new bath tub in your shower room if you have already purchased a brand-new bathtub as well as don't require to alter the arrangement of your previous water system pipes.
Your devices as well as product checklist must comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather problematic due to the restricted access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making sure that the washing machines remain in location in between the tap and the sink. Safeguard the tap in place with the maker given backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Setting up the Tub

Making use of the two wooden boards under its feet, put the bath tub in the required position. The wood boards are helpful in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the bath tub up until the level reviews degree.
To mount taps, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the water system as well as inspect all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill the tub and also examine the overflow outlet and also the normal outlet for leaks.
Finally, fix the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub should wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.

 

 

Preparing for the Installment

Firstly, the supporting frame supplied with the bathroom must be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets system to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final setting.

 

 

Tiling Around the Bathtub

In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, causing issues with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can break relatively early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof adhesive as well as cement.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

Do you appreciate reading up on How to Install a Bathtub Yourself? Put feedback down the page. We'd be delighted to find out your ideas about this page. In hopes that you visit us again later on. Enjoyed reading our review? Please share it. Help others locate it. Kudos for your time. Visit again soon.

Plumbing excellence awaits.